The setting items displayed on the setting menu (see “Basic Operations for Configuring Common Settings”) are shown below. After displaying the setting menu, perform the operation required for the item whose setting you want to change.

Compass Calibration (WF)

Operation

Tap this setting item and then move the watch around as instructed by the Compass magnetic calibration message and animation that appears on the display. A message will appear to let you know when magnetic calibration is complete, and then the screen that was displayed before you started calibration (watch face) will reappear.

Description

This function calibrates Compass so it indicates direction correctly.

If Compass Calibration is dimmed (and will not respond when tapped) it means that Compass accuracy is sufficient and that correction is not required.

Compass Magnetic Declination Calibration (WF/TL)

Operation

Each tap of this setting item toggles between “ON” and “OFF”. The Compass indicates true north when on, and magnetic north when off.

Description

This function corrects magnetic north and true north error.

Altitude Calibration (WF/TL/AC)

Operation

1.

If “Correct Altitude Using Location” is on, turn it off.

2.

Tap “Altitude Calibration”.

3.

On the altitude input screen that appears, input the elevation at your current location (which you obtained from local indications).

• Tap the digit of the value that you want to change, and then use and to change it.

• To reset a manually input altitude calibration value, tap .

Description

You can lessen error in the altitude readings displayed by the watch by manually inputting accurate local altitude and elevation values. You can find out the elevation at your current location from signs, maps, on the Internet, etc. While mountain climbing, it is highly recommended that you make a habit of regularly comparing altitude readings produced by the watch with locally available elevation indications, and of performing this procedure as required.

Correct Altitude Using Location (WF/TL/AC)

Operation

Each tap of this setting item toggles between “ON” and “OFF”.

Description

Select “ON” for this setting to perform auto altitude calibration based on the watch’s or your smartphone’s location information (GPS). “OFF” must be selected for this setting to perform altitude calibration manually using “Altitude Calibration”.

Barometric Pressure Calibration (WF/TL/AC)

Operation

Tapping this setting item displays a barometric pressure input screen. Input the current barometric pressure as measured by another accurate barometer.

• Tap the digit of the value that you want to change, and then use and to change it.

• To reset a manual calibration and display barometric pressure readings based on pressure sensor measurements, tap .

Description

Though the pressure sensor built into the watch is adjusted at the factory and normally does not require calibration, you can perform the calibration operation above if you notice that readings are very different from those from other sources. To calibrate manually, use this item to input the current barometric pressure as measured by another accurate barometer.

Centered value / My Graph (TL)

Operation

Tap this setting item and then scroll the list that appears upwards and downwards. When the type of value you want shown in the center of the My Graph Screen is displayed, tap it.

Description

This setting changes the type of value displayed in the center of the My Graph Screen.

Home city (WF)

Operation

Tap this setting item and then scroll the list that appears upwards and downwards. When the name of the city you want to specify as your Home city is displayed, tap it.

Description

This setting specifies the Home city displayed on watch faces (World Time, Traveler).

Edit Color (WF)

Operation

Tap this setting item, and then on the list that appears tap the color you want to use.

Description

This setting specifies the face color of a watch face (Authentic, Multi, Location, Traveler, etc).

Monochrome Display (WF/TL/AC/TP)

Operation

Each tap of this setting item toggles the face background between “Dark” and “Bright”.

Description

You can select how the watch’s monochrome LCD displays data. This setting is applied to all of the displays below.

• “2 Layers” watch face monochrome display

• TOOL app monochrome display

• Activity app monochrome display

• Multi Timepiece Mode monochrome display

Point Navigation (TL/AC)

Operation

Each tap of this setting item toggles between “ON” and “OFF”.

Description

When the setting of this item is “ON”, an icon indicating the direction to your destination is displayed on the compass color display during navigation with Point Navigation.

GPS Time Calibration (WF)

Operation

1.

Move to an outdoor area where the sky is visible.

2.

Perform the required operation on a CASIO watch face to display the setting menu, and then tap “GPS Time Calibration”.

3.

Carefully read the message that appears on the display and then tap “Correct”.

4.

Wait until GPS reception is complete.

Description

The watch normally adjusts its current time setting by syncing with a smartphone. Should the smartphone battery go dead, if you lose your smartphone, or if syncing is not possible for some other reason, you need to perform the above operation each time you want to adjust the watch’s time setting. Each time you do, the watch will temporarily adjust its time setting based on GPS information.

It is recommended that you perform this procedure in a location where GPS reception conditions are good and where the sky is visible. See “Appropriate and Inappropriate Signal Reception Location”.

Port setting (TL)

Operation

Tap this setting item and then scroll the list that appears upwards and downwards. When the name of the point (port name or name of a city near the ocean) you want is displayed, tap it.

Description

This setting specifies the point (port) whose tide information is displayed by the “Tide Graph” of the TOOL app.

Re-calculation with Current Location (TL)

Operation

Tap this setting item to start acquisition of positioning information for your current location. After positioning information acquisition is successful, the TOOL screen will reappear, which will show re-calculated data.

Description

Perform this operation when “DEMO” is displayed on the TOOL app screen or when the message “Displayed result is based on location info from 000 minutes ago.” appears. It re-calculates data displayed by the TOOL app based on current location information acquired by the watch or your smartphone GPS function.

Save Daily Location Info (WF/MS/LM)

Operation

After tapping this setting, you then need to select “Every 6 minutes”, “Every 1 minute”, or “OFF”.

Description

This item is for configuring a setting related to the Location Memory app.

Selecting “ON” for this item enables maintenance of a daily location history, even when there is no Activity app measurement operation.

Save daily activity records (WF/TL/MS)

Operation

Each tap of this setting item toggles between “ON” and “OFF”.

Description

This item is for configuring a setting related to watch faces (Heart Rate, Authentic, Multi), the TOOL app (My Graph), and the MOMENT SETTER app.

Selecting “ON” for this item, allows the watch to record information (such as displayed workout time and energy consumption) about your activities. If you want to use this function, make sure that its setting is “ON”.

Height (TL/MS)

Operation

Tap this setting item and then use the screen that appears to input your height.

• Tap the digit of the value that you want to change, and then use and to change it.

Description

The value you input for this item is used as basic information when calculating data displayed on the TOOL app’s “My Graph”.

Weight (TL/MS)

Operation

Tap this setting item and then use the screen that appears to input your weight.

• Tap the digit of the value that you want to change, and then use and to change it.

Description

The value you input for this item is used as basic information when calculating data displayed on the TOOL app’s “My Graph”.

Units (WF/TL/AC/MS)

Operation

Each tap of this setting item toggles between “Metric” and “Imperial”.

Description

Use this setting to switch between metric units (meters, kilograms, hPa, etc.) and Imperial units (feet, pounds, inHg, etc.) for values displayed by CASIO watch faces and apps.

Energy Unit (WF/TL/MS/AC)

Operation

Each tap of this setting item toggles between “Cal” (kilogram calories or large calories, default setting) and “kJ” (kilojoules).

Description

The setting you specify here is used for the energy consumption value displayed on watch faces (Authentic, Multi), and by the TOOL app (My Graph), the MOMENT SETTER app and the Activity app.

Wrist where you wear the watch (TL/MS)

Operation

Each tap of this setting item toggles between “Right” and “Left”.

Description

The setting for this item is used as basic information when calculating data displayed on the TOOL app’s “My Graph” and the “Heart Rate” watchface.

Target altitude (AC)

Operation

Tap this setting item and then use the screen that appears to specify a target altitude.

• Tap the digit of the value that you want to change, and then use and to change it.

Description

Use this item to input a target altitude before starting an Activity app Trekking activity.

Target Distance (AC)

Operation

Tap this setting item and then use the screen that appears to specify the distance to a goal.

• Tap the digit of the value that you want to change, and then use and to change it.

Description

Use this item to specify the distance to a goal before starting a Running or Trail Running activity measurement operation. During the Activity measurement operation, the distance remaining to the goal will be displayed based on the value you specify here.

The longer the distance run, the greater the cumulative error in the displayed distance. Because of this, the closer you get to your goal, the less accurate the remaining distance value becomes. You should regard the remaining distance value as a rough estimate.

View Routes Display (AC)

Operation

Each tap of this setting item toggles between “ON” and “OFF”.

Description

Specifies where route data^* imported to the watch should be displayed on a map during Activity measurement operations. Select “OFF” for this setting if the route you will be following is different from the imported route data, or if you want to view your current route without route data. Even if you select “OFF” for this setting, the imported route data will remain in watch memory.

Auto Pause (AC)

Operation

Each tap of this setting item toggles between “ON” and “OFF”.

Description

This setting item is linked with the Running and Cycling activities. While “ON” is selected for this item, the watch detects your movements and automatically pauses the Activity measurement operation when it detects that your movement has stopped (for example, while you are waiting at a traffic light during a run, etc.) or when your movement is extremely slow. Pauses are not included in the measurement data.

Start Countdown (AC)

Operation

Tap this setting item. On the screen that appears, tap or to set a countdown time in the range of 0 to 10 seconds.

Description

This setting item is linked with the Running, Trail Running, Cycling, and Paddle activities. It specifies the countdown time until measurement actually starts from the point when “START” is tapped (or the upper button is pressed) to start one of these Activity measurement operations. Specifying “0 sec (OFF)” for this setting causes the measurement operation to start without a countdown.

Lap (AC)

Operation

After tapping this setting, you then need to select “Every 10 km”, “Every 5 km”, or “Every 1 km”.

Description

This setting item is linked with the Running activity. When a run reaches the distance specified here while using the Running activity, the watch will automatically record a lap time. While a Running measurement operation is in progress, you can display the time of the lap (Lap) you ran previously to your current lap and the average (Lap Average) of all of your laps.

Route Colors (AC)

Operation

From the Activity app, perform the required operation to display the setting menu and then tap “Route Colors”. This displays a screen showing the meanings of the route track colors.

Description

Route tracks are drawn on Activity app maps using multiple colors. This item shows the meaning of each color, and is not used for configuring particular settings.

Auto Record (AC)

Operation

1.

Use the Activity app to display the Snow “START” screen, and then tap “GO”.

2.

Swipe the touch screen from bottom to top and then tap “Settings”.

3.

On the setting menu that appears, swipe upwards and downwards until “Auto Record” is displayed, and then tap it.

• Each tap toggles between “ON” and “OFF”.

Description

This setting is related to the Activity app Snow. When the setting of this item is “ON”, the watch will start an activity measurement operation automatically when operation by you is detected. When “OFF”, you need to start measurement operations manually. The initial default setting is “OFF”.

Map Type (AC/MS/LM)

Operation

Each tap of this setting item toggles between “Google Maps” and “Mapbox”.

Description

This setting lets you select either Google Maps or Mapbox as the map type displayed by the Activity app and Location Memory app.

Map Skin (AC/MS/LM)

Operation

Tap this setting item, and then use the list that appears to tap the name of the map skin you want to use.

Description

This item is for selecting the map skin displayed by the Activity app and the Location Memory app. You can select geographic view, satellite view, or another view to suit your location or purpose.

Download Map (AC/MS/LM)

Operation

1.

Tap “Download Map”.

• This displays a list of map skin names.

2.

Scroll the list upwards and downwards. When the skin name you want is displayed, tap it.

• This displays a map with your current location in the center.

3.

Scroll the map so the location that you want to be in the center of the map you download is in the center of the watch screen.

• You can scroll the map after using the APP button (-) to reduce the size of the map and increase the display area. The area in circle in the center of the screen at this time shows the maximum downloadable area.

4.

Use the MAP button (+) and APP button (-) to zoom the map so the area you want to download fills the screen.

• The area that is displayed at this time is the approximate area that will be downloaded.

5.

Tap “Fix”.

• This may cause a message prompting you to use Wi-Fi to appear.

• This starts map downloading, and show the progress on the display. To cancel downloading, tap ×.

• The downloaded map will appear on the display after download is complete.

Description

This item is for configuring settings related to the Activity app and the Location Memory app. It is for downloading a map to watch memory when “Mapbox” is selected for “Map Type”. If you want to use the map in an area where a network connection is not available, use this item beforehand in an area where a network connection is available to download the desired map.

Downloaded Map (AC/MS/LM)

Operation

Tapping this setting displays the map you downloaded.

• To display another downloaded map, swipe the touch screen from right to left.

• To delete the currently displayed map, swipe the touch screen from bottom to top and then tap “Delete This Map”.

Description

You can use the procedure under “Download Map” to view and delete maps saved in watch memory.

Route Tracking(Activity) (AC/LM)

Operation

Each tap of this setting item toggles between “Accuracy Priority” and “Battery Priority”.

Description

This item is for configuring a setting related to Activity app. While “Accuracy Priority” is selected, the GPS positioning operation and refresh operation are performed more frequently, and the route tracked on the map is more accurate. While “Battery Priority” is selected, the accuracy of the route tracked on the map is reduced somewhat, but battery power is saved.

Except when you want to perform long-term Trekking or Fishing measurement operations, use “Accuracy Priority” for better speed and distance calculation accuracy, and more frequent display refreshing.

All Off (MS)

Operation

1.

Tap this item and a confirmation dialog box will appear asking if you want to disable all MOMENT SETTER notifications.

2.

Tap “Turn off.” to disable notifications or “Cancel” to leave notifications enabled.

Description

Removing all check marks from the MOMENT SETTER app menu disables all notifications. Note that once you perform this operation, there is no single batch operation to re-enable notifications. You will need to use the MOMENT SETTER app menu to individually re-enable each notification you want.

Route Display (LM)

For information about this item, see “Enabling Route Tracking on the Map (Route Display)”.

Revisit (LM)

For information about this item, see “Changing the “Revisit” Mark Notification Setting”.

Total Maximum Heart Rate (WF/MS/AC)

Operation

1.

From the “Heart Rate” watch face or Activity app, display the settings menu and then tap “Total Maximum Heart Rate”.

2.

Select either “Calculate from Birth Month” or “Manual Setting”.

3.

Selecting “Manual Setting” will display an input screen. Use and to manually specify a maximum heart rate and then tap .

Description

The Total Maximum Heart Rate setting can be configured automatically based on the birth information you input, or manually. To specify a total maximum heart rate manually, input a value in the range of 20 to 220. The value you input will be used to calculate heart rate zones. For normal daily training, initially select “Calculate from Birth Month”, which generally will set a relatively low value. After training for some time, you should be able to get a grasp of the maximum heart rate that is best for you, so you will be able to select “Manual Setting” and specify the value you want.

Heart Rate Zone Alert (AC)

Purpose of This Setting

• When doing heart-rate training, this item helps to ensure that your heart rate does not exceed the upper limit of the heart rate zone you are using as your target.

• During a long workout, notification will be performed to warn you against over-exertion.

Operation

1.

If you have not configured your Birth Month and Stable Heart Rate settings, configure them now.

• See “Initial Default Settings for Heart Rate Measurement”.

2.

From the Activity app, perform the required operation to display the setting menu and then tap “Heart Rate Zone Alert”.

3.

Select one of the options that appear.

Option	Description
Target Zone 4 Target Zone 3 Target Zone 2 Target Zone 1	While using Running or Trail Running, a Heart Rate Zone Alert will appear on the display whenever your heart rate exceeds the upper limit of your target zone. If you select “Target Zone 3”, for example, the alert will appear if your heart rate enters Zone 4 during measurement.
OFF	Heart Rate Zone Alert not displayed.

4.

Selecting a setting other than “OFF” will display a screen for selecting a screen option. Select “Display Only” or “Display + Notification”.

Option	Description
Display Only	Exceeding the upper limit of the target zone causes “ZONE” to flash on the Activity app screen (Running or Trail Running measurement screen).
Display + Notification	Along with display of “ZONE” described above, exceeding the upper limit of the target zone causes the watch to perform two short vibrations.

Description

This setting item is linked with the Running, Trail Running, Trekking, Cycling, Paddle, and Snow activities. It triggers an alert whenever the upper limit of the target heart rate zone is exceeded during a measurement operation for all of these activities.