Module No. 5736

Time Correction

Your watch can connect with a phone to obtain information that it uses to correct its date and time setting.

Important!

When you are on an aircraft or in any other location where radio signals area may cause problems, enable the watch’s Airplane Mode to disable connection with your phone.

Using the Watch in a Medical Facility or Aircraft

Referring to the information below, configure the time setting in accordance with the method that suits your own lifestyle.

Do you use a phone?

Time correction by connecting with your phone is recommended.

Getting Ready
Auto Time Correction
w66_img_Lunch_1230_2024

If your phone cannot connect with the watch

You can correct time settings by performing operations on the watch.

Using Watch Operations to Adjust the Time Setting
dg_w66_img_TimeSetting_2_comon

Using Watch Operations to Adjust the Time Setting

If your watch cannot connect with a phone for some reason, you can use watch operations to adjust date and time settings.

Setting a Home City

Use the procedure in this section to select a city to use as your Home City. If you are in an area that observes summer time, you can also configure a summer time setting.

Note

The initial factory default summer time setting for all cities is [AUTO]. In many cases, the [AUTO] setting lets you use the watch without switching between summer time and standard time.

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds.

    3. This causes the current step reminder setting ([ON] or [OFF]) to flash on the display.

    5736_fl_StepRem_comon

  3. Press (C) twice.

    4. This displays the currently selected Home City.

  4. Use (B) and (D) to change the Home City setting.

    5. Holding down (B) or (D) scrolls through settings at high speed.

    For details refer to the information below.

    City Table

  5. Press (C).

  6. Use (D) to select a summer time setting.

    7. Each press of (D) cycles through available settings in the sequence shown below.

    [AUTO]
    The watch switches between standard time and summer time automatically.

    [OFF]
    The watch always indicates standard time.

    [ON]
    The watch always indicates summer time.

    5736_17_ATDS

  7. Press (A) to complete the setting operation.

Setting the Time/Date

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds.

    3. This causes the current step reminder setting ([ON] or [OFF]) to flash on the display.

    5736_fl_StepRem_comon

  3. Keep pressing (C) until the setting you want to change is flashing.

    4. Each press of (C) moves the flashing to the next setting in the sequence shown below.

    fl_Date_Time_seting_Item_28

  4. Configure the date and time settings.

    5. To reset the seconds to 00: Press (D). 1 is added to the minutes when the current count is between 30 and 59 seconds.

    For all the other settings, use (B) and (D) to change the flashing setting.
    Holding down (B) or (D) scrolls through settings at high speed.

  5. Repeat steps 3 and 4 to select time and date settings.

  6. Press (A) to complete the setting operation.

Note

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

Switching between 12-hour and 24-hour Timekeeping

You can specify either 12-hour format or 24-hour format for the time display.

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds.

    3. This causes the current step reminder setting ([ON] or [OFF]) to flash on the display.

    5736_fl_StepRem_comon

  3. Press (C) 10 times.

    4. This causes [12H] or [24H] to flash on the display.

    5736_18_ATDS

  4. Press (D) to toggle the setting between [12H] (12-hour timekeeping) and [24H] (24-hour timekeeping).

    5. 5736_19_fl_ATDS

  5. Press (A) to complete the setting operation.

Note

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

Using the Watch in a Medical Facility or Aircraft

Whenever you are in a hospital, on an aircraft, or in any other location where connection with a phone may cause problems, you can perform the procedure below to disable auto time correction. To re-enable auto time correction, perform the same operation again.

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds.

    3. This causes the current step reminder setting ([ON] or [OFF]) to flash on the display.

    5736_fl_StepRem_comon

  3. Press (C) 14 times.

    4. This displays [RCVD].

    5736_20_ATDS

  4. Press (D) to change the auto time correction settings.

    5. [OFF]: Auto time correction disabled.

    [ON]: Auto time correction enabled.

  5. Press (A) to complete the setting operation.

Note

The auto time correction setting can be changed only while the watch is paired with a phone.

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

Back

Next