Module No. 5736

Other Settings

This section explains other watch settings you can configure.

Specifying the Day of the Week Language

You can select any one of six languages for the day of the week display in the Timekeeping Mode.

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds.

    3. This causes the current step reminder setting ([ON] or [OFF]) to flash on the display.

    5736_fl_StepRem_comon

  3. Press (C) 11 times.

    4. This causes the language setting to flash.

    5736_51_Other

  4. Use (D) to select a language.

    5. [ENG]: English
    [ESP]: Spanish
    [FRA]: French
    [DEU]: German
    [ITA]: Italian
    [PyC]: Russian

  5. Press (A) to exit the setting screen.

Note

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

Enabling the Button Operation Tone

Use the procedure below to enable or disable the tone that sounds when you press a button.

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds.

    3. This causes the current step reminder setting ([ON] or [OFF]) to flash on the display.

    5736_fl_StepRem_comon

  3. Press (C) 12 times.

    4. This causes [KEY♪] or [MUTE] to flash on the display.

    5736_52_Other

  4. Press (D) to select [KEY♪] or [MUTE].

    5. [KEY♪]: Operation tone enabled.

    [MUTE]: Operation tone muted.

    5736_53_Other

  5. Press (A) to exit the setting screen.

Note

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

Note that alarm and timer tones still sound even while the operation tone is muted.

Configuring Power Saving Function Settings

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds.

    3. This causes the current step reminder setting ([ON] or [OFF]) to flash on the display.

    5736_fl_StepRem_comon

  3. Press (C) 15 times.

    4. This displays [PSON] or [PSOFF].

    5736_54_Other

  4. Press (D) to toggle between on and off.

    5. [PSON]: Power Saving enabled.

    [PSOFF]: Power Saving disabled.

  5. Press (A) to exit the setting screen.

Note

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

For details about Power Saving, refer to the information below.

Power Saving Function

Resetting Watch Settings

This section explains how to return the watch settings below to their initial factory defaults.

Watch Settings

Pedometer

Stopwatch

Timer

Alarm

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds.

    3. This causes the current step reminder setting ([ON] or [OFF]) to flash on the display.

    5736_fl_StepRem_comon

  3. Press (C) four times.

    4. This causes the seconds to flash.

    5736_55_Other

  4. Hold down (B) for at least seven seconds. Release when [ALL] and [RESET] stop flashing.

    5. 5736_56_Other

  5. Press (A) to exit the setting screen.

Note

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

Resetting the watch also deletes information for pairing the watch with a phone, and unpair them.

Back

Next