Module No. 3513

Troubleshooting

Altitude Measurement

Q1‏Readings produce different results at the same location.
Watch readings are different from altitude information available from other sources.
Correct altitude readings are not possible.

Relative altitude is calculated based on changes in barometric pressure measured by the watch’s pressure sensor. This means that barometric pressure changes can cause readings taken at the same location to be different. Also note that the value displayed by the watch may be different from the actual elevation and/or sea level elevation indicated for the area where you are located. When using the watch’s altimeter while mountain climbing, it is recommended that you regularly calibrate its readings in accordance with local altitude (elevation) indications.

Q2‏[ERR] appears during measurement.

There may be a problem with the sensor. Try taking another measurement.

If [ERR] keeps appearing after multiple measurement attempts, contact a CASIO service center or your original retailer.

Digital Compass

Q1‏The entire display is flashing.

Abnormal magnetism has been detected. Move away from any potential source of strong magnetism and try taking a reading again.

If the display flashes again, it could mean that the watch itself has become magnetized. Move away from any potential source of strong magnetism, perform 2-point calibration, and then try taking a reading again.

Q2‏[ERR] appears during measurement.

There is a problem with the sensor or there may be a source strong magnetic force nearby. Move away from any potential source of strong magnetism and try taking a reading again. If [ERR] keeps appearing after multiple measurement attempts, contact a CASIO service center or your original retailer.

Q3‏[ERR] appears following 2-point calibration.

[ERR] on the display could indicate a sensor problem.

If [ERR] disappears after about one second, try performing 2-point calibration again.

If [ERR] keeps appearing after multiple attempts, contact a CASIO service center or your original retailer.

Q4‏Direction information indicated by the watch is different from that indicated by a backup compass.

Move away from any potential source of strong magnetism, perform 2-point calibration, and then try taking a reading again.

Q5‏Readings at the same location produce different results.
Cannot take readings indoors.

Move away from any potential source of strong magnetism and try taking a reading again.

Barometric Pressure Measurement

Q1‏The barometric pressure differential graphic is not displayed after barometric pressure measurement.

The barometric pressure differential graphic is not displayed if the barometric pressure measurement value exceeds the allowable measurement range (260hPa to 1,100hPa) or if the barometric pressure differential exceeds ±10hPa. If [ERR] is displayed, there may be a problem with the sensor.

Q2‏[ERR] appears during measurement.

There may be a problem with the sensor. Try taking another measurement. If [ERR] keeps appearing after multiple measurement attempts, contact a CASIO service center or your original retailer.

Temperature Measurement

Q1‏[ERR] appears during measurement.

There may be a problem with the sensor. Try taking another measurement. If [ERR] keeps appearing after multiple measurement attempts, contact a CASIO service center or your original retailer.

World Time

Q1‏The time for a World Time City is not correct.

The summer time setting (standard time/summer time) may be wrong.

Alarm and Hourly Time Signal

Q1‏An alarm does not sound.

Is the watch’s battery charged?

Keep the watch exposed to light until it recharges sufficiently.

Other than the above.

The alarm’s settings may not be configured. Configure the alarm settings.

Q2‏The hourly time signal does not sound.

Is the watch’s battery charged?

Keep the watch exposed to light until it recharges sufficiently.

Other than the above.

The hourly time signal may be disabled. Enable the hourly time signal.

Charging

Q1‏The watch does not work even though it is exposed to light.

The watch stops operating whenever the battery goes dead. Keep the watch exposed to light until it recharges sufficiently.

Q2‏[H], [M], and [L] are flashing on the display.

The watch is in the charge recovery mode. Wait until the recovery process is complete (about 15 minutes). The watch will recover more quickly if you place it in a brightly lit location.

If an alarm, hourly time signal, illumination and/or other power-intensive functions are used within a short period of time, the charging capacity of the battery will drop and cause the watch to go into a charge recovery mode. Function availability will be temporarily limited, but functionality will return after the battery recovers.

3514_80_Batt_QA

Q3‏[CHG] is flashing on the display.

The charge level of the watch is extremely low. Immediately expose the watch to light to charge it.

Other

Q1‏I can’t find the information I need here.

Visit the website below.

https://world.casio.com/support/

Back

Next