Troubleshooting
Signal Reception (Time Calibration Signal)
Q1The watch cannot perform a receive operation.
Is the watch’s battery charged?
Signal reception is not possible while battery power is low. Keep the watch exposed to light until it recharges sufficiently.
Is the watch in the Timekeeping Mode?
The watch cannot receive time calibration signals while auto adjustment is disabled or while the watch is in a mode other than the Timekeeping Mode. Return to the Timekeeping Mode.
Is your Home City setting correct for your location?
The watch will not indicate the correct time if the Home City setting is wrong. Change your Home City setting so it correctly reflects your location.
After checking the above, the watch still cannot perform a receive operation.
Time calibration signal reception is not possible under the conditions described below.
- When watch is at Level 2 power saving
- When the crown is pulled out
- Timer countdown operation in progress
If successful reception is not possible for some reason, you can adjust the time and day settings manually.
Q2The signal receive operation always fails.
Is the watch in a location that is appropriate for signal reception?
Check your surroundings and move the watch to a location where signal reception is better.
Did you avoid touching the watch while the receive operation was in progress?
Minimize movement of the watch and do not perform any watch operation while a receive operation is in progress.
Is there an alarm configured to sound during the same period that the signal receive operation is performed?
Receive stops if an alarm operation starts while it is being performed. Disable the alarm.
Is the signal transmitter in your area transmitting a signal?
The transmitter of the time calibration may not be transmitting a signal.
Try again later.
Q3Signal reception should have been successful, but the watch’s time and/or day is wrong.
Is the time zone where you are using the watch specified correctly?
Specify the time zone where you are using the watch.
Is the hand and/or day indicator alignment correct?
Adjust hand and/or day indicator alignment.
After checking the above, the time and/or day settings is still wrong.
Adjust time and day settings manually.
I can’t pair the watch with a phone.
Q1I’ve never been able to establish a (pairing) connection between the watch and phone.
Are you using a supported phone model?
Check if the phone model and its operating system are supported by the watch.
For information about supported phone models, visit the CASIO Website.
Did you install CASIO WATCHES on your phone?
CASIO WATCHES needs to be installed on your phone in order to connect with the watch.
Install the app on your phone.Are your phone’s Bluetooth settings configured correctly?
Configure the phone’s Bluetooth settings. For details about setting procedures, see your phone documentation.
iPhone Users
- “Settings”
“Bluetooth” On
Android Users
- Enable Bluetooth.
Other than the above.
Some phones need to have BT Smart disabled to use CASIO WATCHES. For details about setting procedures, see your phone documentation.
On the Home Screen, tap: “Menu” “Settings” “Bluetooth” “Menu” “BT Smart settings” “Disable”.
I can’t reconnect the watch and phone.
Q1The watch will not re-connect with the phone after they are disconnected.
Is CASIO WATCHES running?
The watch cannot re-connect with the phone unless CASIO WATCHES is running on the phone. On the phone’s Home Screen, tap the “CASIO WATCHES” icon. Then on the watch, hold down the MODE button (C) for about four seconds.
Have you tried turning your phone off and then back on again?
Turn the phone off and then back on, and then tap the “CASIO WATCHES” icon. Next, on the watch, hold down the MODE button (C) for about four seconds.
Is a timer countdown operation in progress?
Connection with a phone is not possible while there is 30 seconds or less remaining on a countdown timer operation. Stop the countdown operation before connecting with the phone.
Q2I can’t connect while my phone is in the Airplane Mode.
Connection with the watch is not possible while the phone is in the Airplane Mode. After exiting the phone’s Airplane Mode, go to the phone’s Home Screen and tap the “CASIO WATCHES” icon. Then on the watch, hold down the MODE button (C) for about four seconds.
Q3I changed the phone’s Bluetooth from enabled to disabled, and now I can’t connect anymore.
On the phone, re-enable Bluetooth, and then go to the Home Screen and tap the “CASIO WATCHES” icon. Next, on the watch, hold down the MODE button (C) for about four seconds.
Q4I can’t connect after turning off the phone.
Turn on the phone and tap the “CASIO WATCHES” icon. Then on the watch, hold down the MODE button (C) for about four seconds.
Phone-Watch Connection
Q1I can’t establish a connection between the phone and watch.
Have you tried turning your phone off and then back on again?
Turn the phone off and then back on, and then tap the “CASIO WATCHES” icon. Next, on the watch, hold down the MODE button (C) for about four seconds.
Has the watch been re-paired with the phone?
After deleting pairing information from CASIO WATCHES, re-pair the watch and phone.
If you are unable to establish a connection...
Use the procedure below to delete the pairing information from the watch, and then re-pair the watch and phone.
- ①
-
Pull out the crown to the second click.
- ②
-
Hold down (B) for about 10 seconds.
This deletes the pairing information. The second hand will point to
. - ③
-
Push the crown back in.
Changing to a Different Phone Model
Q1Connecting the current watch to another phone.
Pair the watch with the phone.
Auto Time Adjustment by Bluetooth Connection (Time Adjustment)
Q1When does the watch adjust its time?
The watch will connect with the phone and perform auto time adjustment at around 12:30 a.m., 6:30 a.m., 12:30 p.m. and 6:30 p.m. The connection is automatically terminated after auto time adjustment is complete.
Q2Auto time adjustment is not performed at a scheduled time.
Is auto time adjustment not being performed according to its normal schedule?
Note that auto time adjustment is not performed for 24 hours after swapping of the Home Time and World Time, or after the time setting is adjusted manually on the watch. Auto time adjustment will resume 24 hours after either of the above operations is performed.
Is auto time adjustment enabled?
Auto time adjustment will not be performed at the scheduled times unless it is enabled. Enable auto time adjustment.
Q3Time is not displayed correctly.
The phone’s time setting may be incorrect because it is unable to connect with its network due to being out of range, etc. If this happens, connect the phone to its network and then adjust the time setting.
Alarm
Q1The alarm does not sound.
Is the watch’s battery charged?
Keep the watch exposed to light until it recharges sufficiently.
The crown is pulled out.
The alarm will not sound while the crown is pulled out. Push the crown back in to its normal position.
Is the alarm enabled?
Enable the alarm.
Hand Movement and Indications
Q1I don’t know what mode the watch is in.
You can determine the current mode by checking the mode hand position. Use (C) to navigate between modes.
Q2The second hand is jumping at two-second intervals.
Battery power is low. Keep the watch exposed to light until it recharges sufficiently.
Q3All hands are stopped and buttons do not work.
The battery is dead. Keep the watch exposed to light until it recharges sufficiently.
Q4The hands suddenly start moving at high speed.
This is due to the reason (or one of the reasons) below, and does not indicate malfunction. Simply wait until normal hand movement resumes.
- The watch is recovering from a power saving state.
- A time calibration signal is being received and the time setting is being adjusted.
- Watch is connected with a phone to adjust its time setting.
Q5Hands are stopped and buttons do not work.
The watch is in the charge recovery mode. Wait until the recovery process is complete (for about 15 minutes). The watch will recover more quickly if you place it in a brightly lit location.
Q6Why is the current time indicated by the watch is off by a certain amount of time (nine hours, three hours and 15 minutes, etc.)?
The city setting is not correct. Select the correct setting.
Q7The current time indicated by the watch is off by one hour or 30 minutes.
The summer time setting is not correct. Select the correct setting.
Q8The hand and/or day indicator are not aligned correctly.
Strong magnetism or impact can cause the hands and/or the indicator to go out of alignment. Adjust hand and/or day indicator alignment.
- Check the information below to find out how to align the hands and/or day indicator manually.
Crown Operations
Q1Nothing happens when I rotate the crown.
If you do not perform any operation for about two minutes after pulling out the crown (approximately 30 minutes in the case of hand and day indicator alignment), crown operations will automatically become disabled. Push the crown back in to its normal position and then pull it out again to re-enable crown operations.
Top of page