Module No. 5718
Using Watch Operations to Adjust the Time Setting
If your watch cannot connect with a phone for some reason, you can use watch operations to adjust date and time settings.
Selecting a Time Zone
Use the procedure in this section to select the time zone of the city where you are using the watch.
Important!
If you do not specify the time zone where you are using the watch, the current time setting will not be correct after it is adjusted based on a time calibration signal.
-
Pull out the crown to the first click.
-
Rotate the crown to change the time zone.
-
Push the crown back in.
The second hand indicates the currently specified time zone, while the function hand indicates the summer time setting.
The time zone is indicated as a time offset. ±0 hours is indicated when the second hand is at 12 o’clock, with other offsets indicated when it is to the left and right of 12 o’clock. For information about time zone positions, go to the section below.
Tokyo (+9 offset)
![5718_06_ATDS_homecity](fig/5718_06_ATDS_homecity_NHCXILsuaopfgs.png)
Adjusting the Time and Day Setting
-
Pull out the crown to the second click.
-
Rotate the crown to adjust the hour and minute settings.
-
Press (B).
-
Rotate the crown to change the hour setting.
-
Press (B).
-
Rotate the crown to move the second hand to the desired setting for the year ten’s digit.
-
Press (B).
-
Rotate the crown to move the second hand to the desired setting for the year one’s digit.
-
Press (B).
-
Rotate the crown to change the month.
-
Press (B).
-
Rotate the crown to change the day.
-
On a time signal at the top of a minute, push the crown back in.
This enables the hour and minute setting operation.
The second hand will indicate whether the current time is a.m. or p.m.
The 57-second position is a.m., while the 3-second position is p.m.
![5718_07_ATDS_homecity](fig/5718_07_ATDS_homecity_NHCXILnphfjdbe.png)
This enables the hour setting operation.
This enables the year ten’s digit setting operation.
![5718_08_ATDS](fig/5718_08_ATDS_NHCXILorddziro.png)
This enables the year one’s digit setting operation.
![5718_09_ATDS](fig/5718_09_ATDS_NHCXILnoglpnem.png)
This enables the month setting operation.
![5718_10_ATDS](fig/5718_10_ATDS_NHCXILplcwoakp.png)
The function hand will move slightly, indicating that the day setting operation is enabled.
![5718_11_ATDS](fig/5718_11_ATDS_NHCXILdglnmpnd.png)
The function hand will move repeatedly while the day setting is being changed.
To return to the hour and minute setting operation, press (B).
Configuring the Summer Time Setting
The watch’s current time setting can be changed to summer time when required.
[STD]: The watch always indicates standard time.
[DST]: The watch always indicates summer time.
Important!
If the time zone is an area where time calibration signal reception is possible, you can select [AT (AUTO)] for the summer time setting. While [AT (AUTO)] is selected, the first time calibration signal receive operation after the time zone enters the summer time period will cause the watch’s time setting to switch to summer time. The first time calibration signal receive operation after the end of the summer time period is reached will cause the watch’s time setting to switch to standard time.
For information about areas where time calibration signals can be received, see the information below.
-
Pull out the crown to the first click.
-
Hold down (B) for at least one second.
-
Push the crown back in.
The second hand will point to the currently selected time zone.
The function hand points to the current summer time setting.
![5718_12_ATDS](fig/5718_12_ATDS_NHCXILirzesdtp.png)
Each time you hold down (B) for at least one second, the summer time setting will cycle to the next available option.
![5718_13_ATDS](fig/5718_13_ATDS_NHCXILgqcwmqrm.png)