Module No. 3554

Configuring Activity Measurement Display Settings

There are various types of activity measurement screens, and up to 9 screens can be registered for each activity.

From among the registered screens, you can specify which one should be displayed while each activity measurement is in progress.

Important!

You can specify activity measurement screens using the CASIO WATCHES phone app. You cannot use watch operations to configure activity measurement screen settings.

Screen 1 is fixed as “Measurement Screen 1”. Select screens 2 to 9 from among screens that are other than “Measurement Screen 1”.

Measurement Screen 1

3515_121_APP_SET

From among the following, select the screens to be displayed for screens 2 through 9.

Measurement Screen 2

3515_122_APP_SET

Measurement Screen 3

3515_123_APP_SET

You can customize the items that appear in the Num_circle_1 upper, Num_circle_2 middle, and Num_circle_3 lower sections of the measurement screen 1 to 3. You can specify customization items using the CASIO WATCHES phone app.

Heart Rate Measurement Screen

3515_124_APP_SET

  1. Movement time from measurement start

  2. Current heart rate

  3. Target HR zone value

Current time screen

3515_125_APP_SET

  1. Current time

  2. Movement time from measurement start

Altitude screen

3515_126_APP_SET

  1. Altitude of current location

  2. Current heart rate

  3. [DIFF RESET] (Altitude Differential Reset) and the altitude differential

  4. Movement time from measurement start

Barometric pressure screen

3515_127_APP_SET
3515_128_APP_SET

  1. Current barometric pressure

  2. Current temperature

  3. Barometric pressure graph

  4. Current heart rate

  5. Movement time from measurement start

Bearing screen

3515_129_APP_SET

  1. Current bearing

  2. Current bearing angle

  3. Current heart rate

  4. Movement time from measurement start

Almanac screen

3554_130_APP_SET

  1. Date of measurement

  2. Measurement day Moon age

  3. Measurement day sunrise time

  4. Measurement day sunset time

  5. Movement time from measurement start

Altitude navigation screen

3515_131_APP_SET

  1. Shows the current altitude at the scale location

  2. Currently displayed checkpoints

  3. Altitude set for the currently displayed checkpoint

  4. Altitude difference between current altitude and checkpoint

  5. Movement time from measurement start

  6. Current heart rate

A pointer (icon_3475_Mmark_up) to the right of the scale along the left of the screen also indicates the altitude differential between the checkpoint and current altitude. The appearance of the pointer changes as described below.

This pointer:

Means this:
3475_Mmark_UP

Altitude differential of +100 m (Or: +100 ft) or more
3475_Mmark_LEFT

Altitude differential within -100 to 100 m (Or: -100 to 100 ft)
3475_Mmark_DOWN

Altitude differential of -100 m (Or: -100 ft) or more

For information about advanced navigation settings, see the information below.

Specifying Checkpoints Along a Training Course (Altitude Navigation)

Note

Holding down (D) for at least two seconds switches the checkpoint display.

3554_131_APP_SET_checkpoint

Interval timer screen

3515_132_APP_SET

  1. Total measurement time

  2. Interval timer value

  3. Number of repeats

  4. Current heart rate

Note

In the case of INTERVAL TIMER, Screen 1 shows the interval timer screen.

Configuring Settings

Check the connection

Make sure the BLE_mark symbol is shown on the watch display when you perform the procedure below. If BLE_mark is not displayed, refer to the information at the link below.

Connecting with a Phone Paired With the Watch

  1. phone-s Tap the “CASIO WATCHES” icon.

  2. phone-s Tap the “My Watch” tab.

  3. phone-s Select “GPR-H1000” and tap it.

  4. phone-s Select the setting you want to change and then perform the operation shown on the screen.

Back

Next