Module No. 5698

Using Watch Operations to Adjust the Time Setting

If your watch cannot connect with a phone for some reason, you can use watch operations to adjust date and time settings.

Setting a Home City

Use the procedure in this section to select a city to use as your Home City. If you are in an area that observes summer time, you can also configure a summer time setting.

Note

The initial factory default summer time setting for all cities is [AUTO]. In many cases, the [AUTO] setting lets you use the watch without switching between summer time and standard time.

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds. Release the button when the name of the currently selected Home City appears on the display.

    3. This is the setting mode. The hands automatically shift out of the way for easy viewing of the display and other indicators.

    5698_fl_HT_SET_comon

  3. Use (B) and (D) to change the Home City setting.

    4. Holding down (B) or (D) scrolls through settings at high speed.

    For details refer to the information below.

    City Table

  4. Press (C).

  5. Use (D) to select a summer time setting.

    6. Each press of (D) cycles through available settings in the sequence shown below.

    [AUTO]
    The watch switches between standard time and summer time automatically.

    [OFF]
    The watch always indicates standard time.

    [ON]
    The watch always indicates summer time.

    5698_DST_SET_comon

  6. Press (A) to complete the setting operation.

Setting the Time/Date

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds. Release the button when the name of the currently selected Home City appears on the display.

    3. This is the setting mode. The hands automatically shift out of the way for easy viewing of the display and other indicators.

    5698_fl_HT_SET_comon

  3. Keep pressing (C) until the setting you want to change is flashing.

    4. Each press of (C) moves the flashing to the next setting in the sequence shown below.

    fl_Date_Time_seting_Item_18

  4. Configure the date and time settings.

    5. To reset the seconds to 00: Press (D). 1 is added to the minutes when the current count is between 30 and 59 seconds.

    For all the other settings, use (B) and (D) to change the flashing setting.
    Holding down (B) or (D) scrolls through settings at high speed.

  5. Repeat steps 3 and 4 to select time and date settings.

  6. Press (A) to complete the setting operation.

Note

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

Switching between 12-hour and 24-hour Timekeeping

You can specify either 12-hour format or 24-hour format for the time display.

  1. Enter the Timekeeping Mode.

    2. Navigating Between Modes

  2. Hold down (A) for at least two seconds. Release the button when the name of the currently selected Home City appears on the display.

    3. This is the setting mode. The hands automatically shift out of the way for easy viewing of the display and other indicators.

    5698_fl_HT_SET_comon

  3. Press (C) eight times.

    4. This causes [12H] or [24H] to flash on the display.

    5698_17_ATDS

  4. Press (D) to toggle the setting between [12H] (12-hour timekeeping) and [24H] (24-hour timekeeping).

    5. 5698_18_fl_ATDS

  5. Press (A) to complete the setting operation.

Note

While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.

Back

Next