Module No. 3501
Using Watch Operations to Adjust the Time Setting
If your watch cannot connect with a phone for some reason, you can use watch operations to adjust date and time settings.
Setting a Home City
Use the procedure in this section to select a city to use as your Home City. If you are in an area that observes summer time, you can also configure a summer time setting.
Note
The initial factory default summer time setting for all cities is [AUTO]. In many cases, the [AUTO] setting lets you use the watch without switching between summer time and standard time.
-
Enter the Timekeeping Mode.
-
Hold down (A) for at least two seconds. Release the button when the name of the currently selected Home City appears on the display.
-
Use (B) and (D) to change the Home City setting.
-
Press (C).
-
Use (D) to select a summer time setting.
-
Press (A) to complete the setting operation.
![3501_fl_HT_SET_comon](fig/3501_fl_HT_SET_comon_VPCVILtsdheznp.png)
Holding down (B) or (D) scrolls through settings at high speed.
For details refer to the information below.
Each press of (D) cycles through available settings in the sequence shown below.
[AUTO]
The watch switches between standard time and summer time automatically.
[OFF]
The watch always indicates standard time.
[ON]
The watch always indicates summer time.
![3501_15_ATDS](fig/3501_15_ATDS_VPCVILlbqpfbzf.png)
Note
While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.
Setting the Time/Date
-
Enter the Timekeeping Mode.
-
Hold down (A) for at least two seconds. Release the button when the name of the currently selected Home City appears on the display.
-
Keep pressing (C) until the setting you want to change is flashing.
-
Configure the date and time settings.
-
Repeat steps 3 and 4 to select time and date settings.
-
Press (A) to complete the setting operation.
![3501_fl_HT_SET_comon](fig/3501_fl_HT_SET_comon_VPCVILtsdheznp.png)
Each press of (C) moves the flashing to the next setting in the sequence shown below.
![5657_fl_Date_Time_seting_Item](fig/5657_fl_Date_Time_seting_Item_UQIDILlwttpjej.png)
To reset the seconds to 00: Press (D). 1 is added to the minutes when the current count is between 30 and 59 seconds.
For all the other settings, use (B) and (D) to change the flashing setting.
Holding down (B) or (D) scrolls through settings at high speed.
Note
While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.
Switching between 12-hour and 24-hour Timekeeping
You can specify either 12-hour format or 24-hour format for the time display.
-
Enter the Timekeeping Mode.
-
Hold down (A) for at least two seconds. Release the button when the name of the currently selected Home City appears on the display.
-
Press (C) eight times.
-
Press (D) to toggle the setting between [12H] (12-hour timekeeping) and [24H] (24-hour timekeeping).
-
Press (A) to complete the setting operation.
![3501_fl_HT_SET_comon](fig/3501_fl_HT_SET_comon_VPCVILtsdheznp.png)
This causes [12H] or [24H] to flash on the display.
![3501_16_ATDS](fig/3501_16_ATDS_VPCVILumnltvpt.png)
![3501_17_fl_ATDS](fig/3501_17_fl_ATDS_VPCVILcymdpqfl.png)
Note
While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation.