fx-100MS/fx-570MS/
fx-991MS/
(2nd edition / S-V.P.A.M.)
Before Using the Calculator
Calculation Modes and Calculator Setup
Basic Calculations
- ▶Inputting Expression and Values
- ▶Arithmetic Calculations
- ▶Fraction Calculations
- ▶Percent Calculations
- ▶Degree, Minute, Second (Sexagesimal) Calculations
- ▶Multi-Statements
- ▶Using Engineering Notation
- ▶Using Engineering Symbols
- ▶Calculation History and Replay
- ▶Using Memory Functions
Function Calculations
- ▶Pi (π), Natural Logarithm Base e
- ▶Trigonometric Functions, Inverse Trigonometric Functions
- ▶Hyperbolic Functions, Inverse Hyperbolic Functions
- ▶Angle Unit Conversion
- ▶Exponential Functions, Logarithmic Functions
- ▶Power Functions and Power Root Functions
- ▶Integration Calculations
- ▶Differential Calculations
- ▶Rectangular-Polar Coordinate Conversion
- ▶Factorial (!)
- ▶Random Number (Ran#)
- ▶Permutation (nPr) and Combination (nCr)
- ▶Rounding function (Rnd)
- ▶Using CALC
- ▶Using SOLVE
- ▶Scientific Constants (fx-570MS/fx-991MS only)
- ▶Metric Conversion (fx-570MS/fx-991MS only)
Using Calculation Modes
- ▶Complex Number Calculations (CMPLX)
- ▶Statistical Calculations (SD, REG)
- ▶Base-n Calculations (BASE)
- ▶Equation Calculations (EQN)
- ▶Matrix Calculations (MAT) (fx-570MS/fx-991MS only)
- ▶Vector Calculations (VCT) (fx-570MS/fx-991MS only)
Technical Information
Configuring the Calculator Setup
Pressing the key more than three times displays additional setup screens.
Underlined ( ___ ) settings are initial defaults.
Deg Rad Gra
Specifies degrees, radians or grads as the angle unit for value input and calculation result display.
(90°= π/2 radians = 100 grads)
Fix Sci Norm
Specifies the number of digits for display of a calculation result.
Fix: The value you specify (from 0 to 9) controls the number of decimal places for displayed calculation results. Calculation results are rounded off to the specified digit before being displayed.
Example: 100 ÷ 7 = 14.286 (Fix 3)
Example: 100 ÷ 7 = 14.29 (Fix 2)
Sci: The value you specify (from 1 to 10) controls the number of significant digits for displayed calculation results. Calculation results are rounded off to the specified digit before being displayed.
Example: 1 ÷ 7 = 1.4286 × 10-1 (Sci 5)
Example: 1 ÷ 7 = 1.428571429 × 10-1 (Sci 0)
Norm: Selecting one of the two available settings (Norm 1, Norm 2) determines the range in which results will be displayed in exponential format. Outside the specified range, results are displayed using non-exponential format.
Norm 1: 10-2 > |x|, |x| ≧ 1010
Norm 2: 10-9 > |x|, |x| ≧ 1010
Example: 1 ÷ 200 = 5 × 10-3 (Norm 1)
Example: 1 ÷ 200 = 0.005 (Norm 2)
EngON EngOFF
Specifies whether engineering symbols are used (EngON) or not used (EngOFF) during value input. The "Eng" indicator is displayed while EngON is selected.
a+bi r∠θ (CMPLX Mode/EQN Mode only)
Specifies either rectangular coordinates (a+bi) or polar coordinates (r∠θ) for CMPLX Mode/EQN Mode solutions. The "r∠θ" indicator is displayed while polar coordinates (r∠θ) are selected.
ab/c d/c
Specifies either mixed fraction (ab/c) or improper fraction (d/c) for display of fractions in calculation results.
Dot Comma
Specifies whether to display a dot or a comma for the calculation result decimal point. A dot is always displayed during input.
Dot: Period decimal point, comma separator
Comma: Comma decimal point, period separator
Note
To close the setup menu without selecting anything, press .
Initializing the Calculation Mode and Other Settings
Performing the following procedure initializes the calculation mode and other setup settings as shown below.
(CLR)(Mode)
This setting: | Is initialized to this: |
---|---|
Calculation Mode | COMP |
Angle Unit | Deg |
Exponential Display Format | Norm 1, EngOFF |
Complex Number Display Format | a+bi |
Fraction Display Format | a b/c |
Decimal Point Character | Dot |
To cancel initialization without doing anything, press (Cancel) instead of .